Thursday, April 20, 2023

  

Commands for Displaying and Configuring System Message Logs

 describes commands that you can use to view or configure the system message logs. Most commands require admin-level access privileges. For detailed information on required access levels and commands, refer to the 
Brocade
®
 
Fabric
 
OS
®
 
Command
 
Reference
 
Manual
.
Commands for Viewing or Configuring System Parameters and Message Logs
Command
Description
auditCfg
Configures the audit message log.
auditDump
Displays or clears the audit log.
errClear
Clears all error log messages for all switch instances on this control processor (CP).
errDelimiterSet
Sets the error log start and end delimiter for messages pushed to the console.
errDump
Displays the entire error log, without page breaks. Use the -r option to show the messages in reverse order, from newest to oldest.
errFilterSet
Sets an error severity filter for the system console.
errModuleShow
Displays all defined error log modules.
errShow
Displays the entire error log, with page breaks. Use the -r option to show the messages in reverse order, from newest to oldest.
pdShow
Displays the contents of the panic dump and core dump files.
portErrShow
Displays the port error summary.
portLogClear
Clears the port log. If the port log is disabled, this command enables it.
portLogDisable
Disables the port log facility.
portLogDump
Displays the port log, without page breaks.
portLogDumpPort
Displays the port log of the specified port, without page breaks.
portLogEnable
Enables the port log facility.
portLogEventShow
Displays which port log events are currently being reported.
portLoginShow
Displays port logins.
portLogPdisc
Sets or clears the debug pdisc_flag.
portLogReset
Enables the port log facility.
portLogResize
Resizes the port log to the specified number of entries.
portLogShow
Displays the port log, with page breaks.
portLogShowPort
Displays the port log of the specified port, with page breaks.
portLogTypeDisable
Prevents an event from being reported in the port log. Port log events are described by the portLogEventShow command.
portLogTypeEnable
Configures an event to be reported in the port log. Port log events are described by the portLogEventShow command.
rasAdmin
Used to enable or disable logging for selected messages or modules, to change the default severity level for a specified message, to display configured RASLog message settings, and to enable or disable quiet time.
rasMan
Displays message documentation on the switch.
setVerbose
Sets the verbose level of a particular module within the Fabric OS.
Commands for Viewing or Configuring System Parametrs and Message Logs
Command
Description
snmpConfig
Manages the SNMP agent configuration.
supportFfdc
Enables and disables FFDC.
supportFtp
Sets, clears, or displays support FTP parameters or a time interval to check the FTP server.
supportSave
Collects RASLog, trace files, and supportShow (active CP only) information for the local CP and then transfers the files to an FTP server. The operation can take several minutes.
supportShow
Issues a list of diagnostic and error display commands. This output is used by your switch service provider to diagnose and correct problems with the switch. The output from this command is very long. Refer to the following related commands: 
supportShowCfgShow
—Displays the groups of commands enabled for display by the 
supportShow 
command. 
supportShowCfgEnable
—Enables a group of commands to be displayed under the 
supportShow 
command. 
supportShowCfgDisable
—Disables a group of commands under the supportShow command.
syslogadmin --set - facility
Changes the syslogd facility.
syslogadmin --set - ip
Adds an IP address as a recipient of system messages.
syslogadmin -- remove -ip
Removes an IP address as a recipient of system messages.
syslogadmin --show - ip
Displays the currently configured IP addresses that are recipients of system messages.
traceDump
Displays, initiates, or removes a Fabric OS module trace dump.

No comments: